WÄHRUNGEN     (Info?)
|
 
  Matho Models
Sie sind hier: Katalog > Zubehör > 3D-Druck > 35045
 
 
 
Plastic Garden ChairsPlastic Garden ChairsPlastic Garden Chairs
Plastic Garden ChairsPlastic Garden ChairsPlastic Garden Chairs
Plastic Garden Chairs  
   

Matho Models 35045 Plastic Garden Chairs

    1 Bewertung(en) | Auch eine Bewertung schreiben
 
€9.95 (€8.22 ex. VAT)
Zur Zeit nicht verfügbar
Erwartet zurück: September 2019
 
ZUR WUNSCHLISTE
WEITEREMPFEHLEN

Produktverfügbarkeit

 
siehe Informationen über.

Was sind die Versandkosten?

Eine Übersicht über die Versandkosten finden Sie hier.

Versanden Sie nach mein Land?

Wir liefern weltweit, also ja, wir versanden zu Ihrem Land!

Wie kann ich bezahlen?

Wir nehmen Zahlung über Kreditkarte, Sofort Banking, Paypal, Banküberweisung, Bankcontact, iDeal oder Barzahlung bei Abholung. Mehr Informationen hier.
Produktdetails
Maßstab: 1:35
Artikelcode: 35045
Hersteller: Matho Models
Weitere Infos: www.mathomodels.com
Produktbeschreibung

Contains 2 unpainted chairs, printed in very high detail UV cured acrylic plastic.

Each chair is 2,7 cm in height (1,06") 

How to work with 3D printed parts?

  1. Be carefull when manipulating 3D printed parts, they can be brittle!
  2. Firstly rinse in Acetone to wash off any excess waxy material. The waxy material is a support material used during 3D printing process. It is very liquid, oil-like and washes off very easily.
  3. After that you can start sanding where needed. The 3D printing process builds up a product in micro-layers. Those layers sometimes remain slightly visible in some areas (especially under magnification), they can be sanded out with a medium sandpaper (like 600 grit), followed by a fine sandpaper (like 1000 grit). Again, the material is not that hard, so it sands very easy. Rinse in Acetone again to wash of any dust.
  4. Some 3D printed models are hollow and open at the bottom that is normally not displayed. Should you do want to display the bottom, simply fill the part with putty and sand.
  5. Now it is ready to prime and paint.

Tip for sanding very small and difficult areas

Cut a small strip of sandpaper 1 - 2 mm wide, fold it and grab it with a tweezers (not the one with a pointy tip, but the one with a flat 1 - 2mm broad tip). Hold it in such a way that the fold is sticking out for only a tiny fraction (make sure it is the fold that is sticking out, and not the loose ends of the strip). Keep holding the tweezers like that and move over the surface you want to sand. When the sandpaper is clogged, make a new fold in an area of the strip that has not been used before, and continue like before. 

See the image below, it explains it all:


How to sand?
click to enlarge

UNSEREN ANDEREN NEUEN PRODUKTEN
 

Mehr kaufen? Mehr sparen!
Schnellsuche
Suchen
Top Artikel
Wir verkaufen auch



Wir Akzeptieren



 
   
  © Copyright 2014 - 2019 Matho Models. All Rights Reserved.
Adresse: Erfgoedlaan 7 - 9800 Deinze - BELGIËN
Tel.: +32 (0) 477 49 13 61 - E-mail: sehe Kontaktseite
website by Matho Graphics  
  Alle Preise sind inklusive Mehrwertsteuer für EU-Kunden, und ohne Mehrwertsteuer für Nicht-EU-Kunden, sofern nicht anders angegeben.