VALUTA     (Info?)
|
 
  Matho Models
U bent hier: Winkel > Accessoires > 3D Printed > 35045
 
 
 
Plastic Garden ChairsPlastic Garden ChairsPlastic Garden Chairs
Plastic Garden ChairsPlastic Garden ChairsPlastic Garden Chairs
Plastic Garden Chairs  
   

Matho Models 35045 Plastic Garden Chairs

    1 review(s) | Schrijf ook een Review
 
€9.95 (€8.22 ex. VAT)
KOOP NU
 
OP VERLANGLIJST
VERTEL EEN VRIEND

Product Beschikbaarheid

 
doorgaans verzonden binnen de 1 - 2 werkdagen.

Wat zijn de verzendkosten?

Voor een overzicht van de verzendkosten, klik hier.

Verzend u naar mijn land?

Wij verzenden wereldwijd, dus ja, wij verzenden naar uw land!

Hoe kan ik betalen?

Wij aanvaarden betalingen met kredietkaart, iDeal, Bankcontact, Paypal, Overschrijving, Sofort banking of Cash bij afhaling. Meer info hier.
Product Details
Schaal: 1:35
Artikelcode: 35045
Fabrikant: Matho Models
Meer info: www.mathomodels.com
Toegevoegd op: woensdag, 02 maart 2016
Product Beschrijving

Contains 2 unpainted chairs, printed in very high detail UV cured acrylic plastic.

Each chair is 2,7 cm in height (1,06") 

How to work with 3D printed parts?

  1. Be carefull when manipulating 3D printed parts, they can be brittle!
  2. Firstly rinse in Acetone to wash off any excess waxy material. The waxy material is a support material used during 3D printing process. It is very liquid, oil-like and washes off very easily.
  3. After that you can start sanding where needed. The 3D printing process builds up a product in micro-layers. Those layers sometimes remain slightly visible in some areas (especially under magnification), they can be sanded out with a medium sandpaper (like 600 grit), followed by a fine sandpaper (like 1000 grit). Again, the material is not that hard, so it sands very easy. Rinse in Acetone again to wash of any dust.
  4. Some 3D printed models are hollow and open at the bottom that is normally not displayed. Should you do want to display the bottom, simply fill the part with putty and sand.
  5. Now it is ready to prime and paint.

Tip for sanding very small and difficult areas

Cut a small strip of sandpaper 1 - 2 mm wide, fold it and grab it with a tweezers (not the one with a pointy tip, but the one with a flat 1 - 2mm broad tip). Hold it in such a way that the fold is sticking out for only a tiny fraction (make sure it is the fold that is sticking out, and not the loose ends of the strip). Keep holding the tweezers like that and move over the surface you want to sand. When the sandpaper is clogged, make a new fold in an area of the strip that has not been used before, and continue like before. 

See the image below, it explains it all:


How to sand?
click to enlarge

Ontdek onze overige nieuwigheden
 

Meer kopen? Meer besparen!
Snel zoeken
ZOEKEN
Aanbevolen
Wij verkopen ook op



Wij Aanvaarden



 
   
  © Copyright 2014 - 2019 Matho Models. Alle Rechten Voorbehouden.
Adres: Erfgoedlaan 7 - 9800 Deinze - BELGI╦
Tel.: +32 (0) 477 49 13 61 - E-mail: zie contact pagina
website by Matho Graphics  
  Alle geafficheerde prijzen zijn inclusief BTW voor EU-klanten, and exclusief BTW voor niet-EU-klanten, tenzij anders aangeduid.