DEVISES     (Info?)
|
 
  Matho Models
Vous êtes ici: Catalogue > Accessoires > 3D > 35040
 
 
 
Plastic Crates APlastic Crates APlastic Crates A
Plastic Crates APlastic Crates APlastic Crates A
Plastic Crates APlastic Crates APlastic Crates A
Plastic Crates A  

Matho Models 35040 Plastic Crates A

pas de critiques | Soyez le premier à laisser un avis!
 
€8.95 (€7.40 ex. VAT)
ACHETER
 
À SOUHAITS
DIRE À UN AMI

Disponibilité du produit

 
Habituellement expédié sous 1 - 2 jours ouvrables.
This product is also available at our dealers.

Quels sont les frais de port?

Une vue d'ensemble des frais d'expédition peuvent être trouvés ici ici.

Envoyez-vous à mon pays?

Nous expédions dans le monde entier, alors oui, nous envoyons à votre pays!

Comment puis-je payer?

Nous acceptons le paiement via Carte de Crédit, Paypal, Virement, Bankcontact, iDeal, Sofort Banking ou Paiement comptant sur collection. Plus d'info ici.
Produit Détails
Échelle: 1:35
Code de l'article: 35040
Fabricant: Matho Models
Ajouté le: lundi 01 février 2016
Description du produit

Contains 2 unpainted crates, printed in very high detail UV cured acrylic plastic.

size (length x width x height) 1,2 x 0,8 x 0,5 cm (0,47" x 0,31" x 0,2")

How to work with 3D printed parts?

  1. Be carefull when manipulating 3D printed parts, they can be brittle!
  2. Firstly rinse in Acetone to wash off any excess waxy material. The waxy material is a support material used during 3D printing process. It is very liquid, oil-like and washes off very easily.
  3. After that you can start sanding where needed. The 3D printing process builds up a product in micro-layers. Those layers sometimes remain slightly visible in some areas (especially under magnification), they can be sanded out with a medium sandpaper (like 600 grit), followed by a fine sandpaper (like 1000 grit). Again, the material is not that hard, so it sands very easy. Rinse in Acetone again to wash of any dust.
  4. Some 3D printed models are hollow and open at the bottom that is normally not displayed. Should you do want to display the bottom, simply fill the part with putty and sand.
  5. Now it is ready to prime and paint.

Tip for sanding very small and difficult areas

Cut a small strip of sandpaper 1 - 2 mm wide, fold it and grab it with a tweezers (not the one with a pointy tip, but the one with a flat 1 - 2mm broad tip). Hold it in such a way that the fold is sticking out for only a tiny fraction (make sure it is the fold that is sticking out, and not the loose ends of the strip). Keep holding the tweezers like that and move over the surface you want to sand. When the sandpaper is clogged, make a new fold in an area of the strip that has not been used before, and continue like before. 

See the image below, it explains it all:


How to sand?
click to enlarge

Produits connexes
AVEZ-VOUS VU NOS AUTRES PRODUITS RÉCENTS?
 

Acheter plus? Économisez plus!
Rechercher
Rechercher
En Vedette
Nous vendons aussi



Nous Acceptons



 
   
  © Copyright 2014 - 2024 Matho Models. All Rights Reserved.
Adresse: Erfgoedlaan 7 - 9800 Deinze - BELGIQUE
Tel.: +32 (0) 477 49 13 61 - E-mail: voir la page contact
website by Matho Graphics  
  Tous les prix indiqués incluent la TVA pour l'UE-clients, et sont hors TVA pour les non-UE-clients, sauf mention contraire.